Introduction: Nominal amp-hours look alike, but usable watt-hours and depth of discharge decide how much practical runtime a 12V 100Ah SLA or LiFePO4 battery can deliver.
A camper, boater, or off-grid cabin owner often compares a 100Ah sealed lead-acid (SLA) bank with a 12.8V 100Ah LiFePO4 replacement and expects the same runtime. The labels look close, and the physical case may even fit the same tray. Physical fit is only the beginning; charger settings and system checks still shape the outcome. The useful comparison is different: how many watt-hours can each battery deliver before its voltage cutoff, how deeply can it be cycled without wrecking life, and how much energy is lost in charging? Those questions explain why two 100Ah batteries can behave very differently in real use.
Amp-hours measure charge, not energy. To get energy in watt-hours, multiply nominal voltage by amp-hours. A 12V 100Ah SLA battery has roughly 1,200Wh of nominal energy (12 × 100), while a 12.8V 100Ah LiFePO4 battery has 1,280Wh (12.8 × 100). That small voltage difference already changes the starting arithmetic. The Surlon Power LFP 12.8V100Ah example is rated at 12.8V, 100Ah, and 1,280Wh, so it illustrates the calculation cleanly. The bigger difference is how much of that nominal energy a user can actually draw. A 100Ah label describes a lab-style capacity point under defined conditions. In the field, usable energy shifts with load profile, temperature, cutoff voltage, battery age, and the way the battery is charged. Lead-acid and LiFePO4 also respond differently to those conditions. The result is that a 100Ah SLA battery and a 100Ah LiFePO4 battery can have different practical watt-hours even before any product-specific settings are applied. That is why a direct comparison should convert both labels to watt-hours first, then adjust each figure for the way the battery will be cycled. The same calculation applies to a custom LiFePO4 battery built for a specific device.
Depth of discharge (DoD) is the share of rated capacity taken out before recharging. A 50% DoD on a 100Ah battery uses about 50Ah; an 80% DoD uses about 80Ah. This is where nominal ratings turn into practical capacity. A battery may be rated for 100Ah, but the system design may only allow part of that range to be used regularly. Two batteries with the same Ah label can therefore behave like different-sized fuel tanks once the planned DoD is applied. The usable watt-hour figure is therefore a design choice as much as a chemical property.
Lead-acid batteries are commonly planned around a shallower cycle, often near 50% DoD for regular use, because deeper discharges shorten service life and can leave less reserve for recovery. That practice turns a 12V 100Ah SLA battery with 1,200Wh nominal into roughly 600Wh of regularly usable energy in many planning scenarios. The exact figure depends on the battery design, load, temperature, and charging routine. Lead-acid capacity also falls more noticeably under heavier loads, an effect often described through the Peukert relationship. For a camper running lights and a small fridge, that means the practical runtime is not simply 100Ah divided by load current.
LiFePO4 systems are often planned to use a deeper share of rated capacity, commonly around 80% to 90% in a well-matched system, while keeping a reserve above the low-voltage cutoff. In that range, a 12.8V 100Ah LiFePO4 battery has an advantage that goes beyond its higher nominal voltage: more of its 1,280Wh nominal energy is treated as usable. The integrated BMS also enforces overvoltage, undervoltage, short-circuit, and over-temperature protection, so the cutoff is not left to guesswork. The usable figure still moves with load, temperature, cutoff settings, and charger behavior, but the planning range is generally deeper than the lead-acid norm.
Voltage cutoff sets the floor and ceiling of the usable range. A low-voltage cutoff that is set high protects the battery but leaves more capacity unused; a cutoff that is set low extracts more energy but can stress the cells. In a 12.8V 100Ah LiFePO4 battery, the BMS manages this boundary, and the system designer decides where the inverter or load should stop. Lead-acid behaves differently: voltage sags under load, so a load that works at rest may hit cutoff earlier under a heavy draw. That sag reduces apparent usable capacity and makes the load profile part of the capacity story. Cycle efficiency adds a second loss layer. Round-trip efficiency is the share of energy put in that comes back out during discharge. General battery references describe lithium chemistries as having high cycle efficiency, while lead-acid loses more energy during charging, especially in the later absorption stage. Those losses mean that equal wall-plug energy does not produce equal delivered watt-hours. For planning, the useful number is delivered watt-hours, not the nameplate watt-hour figure alone. The 1,280Wh value for the Surlon Power LFP 12.8V100Ah example is nominal energy; usable output depends on cutoff, load, temperature, and BMS settings. When a pack finally leaves service, used lithium-ion batteries belong in a dedicated recycling stream, and the US EPA offers general end-of-life guidance.
A 100Ah rating is a starting point, not a runtime promise. The useful comparison is watt-hours after voltage, depth of discharge, cutoff, load behavior, and cycle efficiency are considered. A 12V 100Ah SLA battery usually gives up a larger share of its nominal capacity to shallow cycling and charging losses, while a 12.8V 100Ah LiFePO4 battery such as the Surlon Power LFP 12.8V100Ah example offers more usable energy within a well-matched system. For a real installation, the product specifications and BMS settings are the right place to confirm the final capacity expectation. That is the number to compare when runtime matters.
A: No. A 100Ah LiFePO4 battery usually provides more usable watt-hours because its nominal voltage is slightly higher and its practical depth of discharge is deeper. A 12.8V 100Ah LiFePO4 example has 1,280Wh nominal, while a 12V 100Ah SLA battery has about 1,200Wh nominal; after depth of discharge and cutoff losses, the LiFePO4 pack often delivers more of that rating in real use.
A: Depth of discharge determines how much of the rated capacity can be used regularly. Lead-acid batteries are often kept to a shallower cycle to protect life, so only part of their 100Ah rating becomes practical runtime. LiFePO4 systems can usually be planned across a deeper range, so more of the rated capacity is available while still keeping a reserve above the low-voltage cutoff.
A: Voltage cutoff sets how much energy the BMS allows before discharge stops, and a high cutoff leaves more capacity unused. Cycle efficiency then accounts for energy lost in charging and discharging. The 1,280Wh rating is nominal, so usable watt-hours are lower and depend on cutoff settings, load profile, temperature, and BMS behavior.
Alternative Fuels Data Center: Batteries for Electric Vehicles
Used Lithium-Ion Batteries | US EPA