Application design example: This case uses Surlon Power's published reference-pack data. The monitoring-node brief, energy assumptions and proposed checks are illustrative, not a report of a completed customer installation.
A soil monitoring node may spend most of its time asleep, wake to read sensors and briefly transmit data. Its battery must bridge the periods when solar charging is unavailable. For an OEM developing this equipment, the design question is not simply whether a battery can power the electronics. It is whether the complete node can meet its reporting schedule through the agreed weather conditions and service interval.
This example considers a stationary node with soil sensors, a controller and a wireless modem. It evaluates the Surlon Power 6.4V 12Ah custom LiFePO4 battery pack as a candidate for technical review. The battery is not presented as a complete solar power system or a pre-approved outdoor solution.
The listed reference uses a 32700 2S2P configuration, with 6.4V nominal voltage and 12Ah nominal capacity. Multiplying those values gives 76.8Wh nominal energy. The published reference weight is 642g.
Two mechanical layouts are listed: 65 × 65 × 74mm and 33 × 129 × 72mm. They are alternatives, not interchangeable compartment dimensions. The selected layout, tolerances, harness and protection requirements need to be confirmed before enclosure tooling or a sample order.
For a transparent first estimate, assume the node consumes 0.15W averaged across the full day, measured at the battery terminals. This includes sleep, sensing, voltage conversion and scheduled radio transmissions. Daily energy demand would be 0.15W × 24 hours, or 3.6Wh.
Keeping a 30% planning allowance from nominal energy leaves 53.76Wh for this example. Dividing by 3.6Wh per day gives approximately 14.9 days without charging. That result is an illustrative screening estimate, not a guaranteed autonomy rating. The allowance is a design assumption, not a measured usable-capacity specification.
If weak radio coverage raises average consumption to 0.30W, the same calculation falls to about 7.5 days. Record unsuccessful transmissions, reconnection attempts and sensor warm-up energy in the actual field profile. Temperature, aging, cut-off settings and self-consumption can further change the result.
A nominal 6.4V label does not specify the required charging voltage or a suitable solar panel. Request the approved charging profile, voltage limits, termination behavior and charging-temperature range for the ordered build. The product summary lists 12A maximum charge current; that is a limit to review, not a recommended solar charge setting.
The solar charge controller must match the battery chemistry and the complete operating window. Assess panel output for the installation location and season, including shading and conversion losses. A panel that replaces one day's energy in good sunlight may not restore the battery promptly after several low-generation days. Define both a daily energy balance and a recovery target.
Average demand can conceal brief current peaks when a modem transmits. Capture the battery-terminal current waveform and check voltage at the electronics during those events. Review cable resistance, regulator response and protection behavior with the supplier.
The reference sheet lists 30A maximum discharge and 60A instantaneous discharge, but does not define pulse duration or test conditions for the latter. Those entries do not establish the suitability of the complete node. Obtain the approved duty limits rather than designing around an unspecified peak rating.
Specify what happens when energy becomes limited: fewer reports, local data storage or an orderly shutdown may be preferable to repeated resets. Any recovery strategy must be tested with the real controller and charging system.
The blue-wrapped battery assembly should not be assumed to be weatherproof. Select an equipment enclosure and cable-entry arrangement for rain, condensation, dust and the installation environment. Review heat buildup in sunlight and the temperatures at which charging is permitted.
Allow room for insulation, mounting support, strain relief and service access. The product photographs show red and black leads without a defined mating connector. Agree on termination, polarity, wire length and the assembly drawing; do not rely on wire color alone for commissioning.
The useful outcome is a measurable acceptance plan and a clearer OEM inquiry. Actual autonomy and environmental performance remain subject to the approved configuration and testing. For a different energy requirement or installation envelope, explore the custom LiFePO4 battery pack range.
Send the full input-voltage range, measured daily energy, wireless peak current and duration, target no-sun autonomy, proposed solar controller, battery-compartment drawing and operating environment. Include the sample quantity, estimated annual volume, destination market and required documentation.
Request a custom soil monitoring battery quotation or email market@surlonpower.com with the subject Solar Soil Monitoring Battery — 6.4V 12Ah Evaluation. Reference LFP32700-2S2P and identify the mechanical layout you want reviewed.